application will restarted after的搜索结果
-
1
abaqus计算出现Application restarted after 449 minutes，the license will be checked within the next 3 minutes。请问这个代表重新开始之前软件没进行计算吗？怎么设置，避免重启 -
0
abaqus计算一个模型到一定时间后，计算一直显示运行，但是计算时间却不更新。出现以下情况，求各位大咖解答一下。谢过了。。
-
1
模型为explicit打桩过程对已经建成隧道的影响，算到一半就会显示Application restarted after 60 minutes of idle time; the license will be checked within the next 3 minutes.，求各位大神帮忙看一下，应该怎么办，附件（1）是我的模型 。附件（1） moxing.zip
-
4
ERROR40524： number of slave nodes in eroding contact interface #2 exceed initial number please restart after setting flag to active the interior node option 附上K文件
-
2
Please restart after setting flag to activate the -interior node option-.
-
4年前 子弹侵彻多层靶板。求教大神问题？1
计算过程中出现error: number of slave nodes in eroding contact interface #11exceeding initial number. pleast restart after setting flag to activate the -interior node option-请问该如何修改K文件，消除该错误 谢谢大神指教？
-
2
Please restart after setting flag to activate the -interior node option-.
-
9年前 求助：dyna侵蚀接触error3
子弹和钢板之间定义eroding surface to surface接触，子弹part做主面，钢板part做为从面，计算过程中出现error: number of slave nodes in eroding contact interface #1 exceeding initial number. pleast restart after setting flag to activate the
-
1
REFORMED AFTER EACH 3 ITERATIONS-- **TIMESTEP WILL BE REDUCED DUE TO DIM.
-
7年前0
your application”，这个要怎么改，哪位帮忙看一下...
-
158814
This capability is most useful in the hydraulics applications of FLOW-3D. -
8
Please check to see if the selected set of elements has changed after restarting this analysis. 2如果我按照：选择施加对流系数节点->生成表面效应单元->施加对流系数->求解->生死单元去除->删除对流系数->循环回第一步，这种顺序的话会报很多相同的警告，但能算下去，但实际结果和没有对流系数是一样的
-
1828
After installing MCR, the VBEA.exe can be launched directly. Please note that the first launching of the program takes one to two minutes.
-
569
You should have "c:\windows\system32>_" in the black window Type in the following one after the other and press enter.
-
12年前 SCP回弹补偿不能计算——求各位大侠指导3
我用dynaform的SCP模块，按照DF5.7_Application_Manual.pdf中的顶盖补偿例子一步步做的(5.6和5.7我都试过，出现的错误是一样的，回弹结果是很好的，就是补偿计算不了)，补偿计算时总是出现如下错误： *** Error line number 18 contains improperly formatted data (This is line
-
6年前 abaqus屈曲分析
180
选择*RESTART块，单击add after，在其后添加*node file u,向结果文件中写入模态分析的位移。 ④使用屈曲特征模态扰动网格，要选择扰动量级的大小，以便网格能够正确地实现后屈曲变形。一般来讲，用于不同特征模态的扰动量级分别只有相应结构尺寸（比如壳的厚度）的百分之几。因为最小特征模态与撞击关系最密切，所以相应的扰动量级应该最大。 -
17年前 铸造之星FT-STAR 科研项目简介191695
The computation speed of the simulation system was remarkably increased after the modifications and meets the requirements for practical applications. 3.
-
2
DETERMINANT TETRA N/A 9 N/A N/A N/A N/A 5247 1103 N/A IN THE ABOVE TABLE INDICATES TESTS THAT ARE NOT APPLICABLE
-
7
但是启动程序后，Patran加载到最后，找到license，提示错误如下: Error reported from application Security You have requested to run MSC.Patran on a Windows T***(10a105a14d**) (Windows 5.1 (Build 2600: Service Pack 3)).
-
2
a restart file is written and ls-dyna terminates. sw2. ls-dyna responds with time and cycle numbers. sw3. a restart file is written and ls-dyna continues calculations. sw4.
